Industrial IoT (IIoT)
Predictive Maintenance in Aerospace: How Sensors Find Problems Earlier
Published by IOT Washington Research & Editorial Team

- Why Fixed Schedules Are Not Enough
- The Sensors That Matter Most
- From Raw Signal to Useful Warning
- Results Reported Across Industry
- What Washington Shops Can Take From It
- How to Start a Program
- Limits and Pitfalls
- Reading the Data: What Changes Mean
- Maintenance Organizations and the Business Case
- Regulation and Trust in the Data
- A Worked Example: A Machining Cell
- Choosing a Vendor or Building In House
- Where It Is Headed
Aircraft are inspected on a schedule, but failures do not follow schedules. Predictive maintenance tries to close that gap by watching the condition of components as they run and flagging changes before they become faults. In aerospace the stakes are unusually high, since an unplanned engine removal or a grounded airplane costs far more than the part itself.
This article explains which sensors do the work, how the data is turned into warnings, and what the same ideas mean for Washington manufacturers and maintenance providers.
Why Fixed Schedules Are Not Enough
Industry studies commonly find that most equipment failures are random rather than tied to age. One often cited figure is that about 82 percent of failures show no clear age pattern. If that is true, replacing parts on a calendar wastes good components and still misses many real faults. Condition-based approaches aim to replace what is actually wearing out, and to do it before it fails.
The Sensors That Matter Most
| Sensor | What it detects | Typical use |
|---|---|---|
| Vibration | Imbalance, bearing wear, misalignment, looseness | Engines, gearboxes, rotating machinery |
| Oil debris | Metal particles shed by wearing parts | Engine and transmission health |
| Temperature and pressure | Overheating, leaks, blocked flow | Hydraulic, fuel and bleed systems |
| Strain and acoustic | Cracks and fatigue in structures | Airframe and composite monitoring |
| Electrical current | Motor and actuator degradation | Ground equipment and production machines |
Vibration is the workhorse. Vibration sensors hold roughly a third of the engine health sensor market by some estimates, and health and usage monitoring systems, known as HUMS, rely on them heavily. Meggitt-style engine vibration monitors are fitted to nearly all civil transport aircraft.
Oil debris monitoring is a close second. In July 2026 Gastops marked its 20,000th MetalSCAN unit, a sign of how common inline particle detection has become. When a bearing starts to shed metal, the sensor sees particles long before oil analysis in a lab would.
From Raw Signal to Useful Warning
- Collect. Sensors sample continuously, often at high rates for vibration.
- Process at the edge. Local hardware filters noise and extracts features so only useful data travels.
- Compare to a baseline. The system knows what normal looks like for that engine or machine and flags drift.
- Predict. Models estimate remaining useful life, increasingly using physics-informed methods blended with machine learning. HBK's Monitor360, released in 2026, follows this edge and AI approach.
- Act. A work order is raised so the part is replaced during planned downtime rather than after failure.
The last step is the one most programs fail at. A warning that no one owns produces no value. Successful teams define in advance who responds to which alert and how fast.
Results Reported Across Industry
Studies of predictive maintenance commonly report downtime reductions between 35 and 50 percent, and McKinsey has cited maintenance cost reductions of 18 to 25 percent. Those figures come from mixed industries and depend on the starting point, so treat them as a range rather than a promise. RFID tool tracking, a neighboring technology, has been reported to cut lost tools by 80 to 90 percent, which shows how much hidden waste there is in maintenance work.
What Washington Shops Can Take From It
Washington has an aircraft maintenance and repair presence as well as manufacturing. But the lessons also apply to the machines that make aircraft parts. A five-axis mill or an autoclave is a rotating, heated, pressurized asset that behaves like a smaller version of what flies. Vibration and current monitoring on production machines is inexpensive and mature. Our coverage of predictive maintenance for Everett aerospace suppliers and the statewide piece on predictive maintenance in Washington give practical starting points.
Edge processing matters here too, because shop floors often cannot send every sample to the cloud. See edge computing in Washington for how that works.
How to Start a Program
- Rank assets by cost of failure. Begin with machines whose downtime stops a line or ruins expensive work.
- Install the simplest useful sensor. Vibration and temperature cover many failure modes.
- Collect baseline data first. Weeks of normal operation are needed before alerts mean anything.
- Set thresholds with maintenance staff. The people who fix machines know which changes matter.
- Track results. Count avoided failures, saved downtime and false alarms, and adjust.
Limits and Pitfalls
False alarms erode trust quickly, so tune alerts before rolling out widely. Sensor placement affects signal quality, and a poorly mounted accelerometer can mislead. Data quality and cybersecurity need attention as well. Finally, predictive models cannot see what is not measured, so keep inspections in place for failure modes that sensors do not cover.
Reading the Data: What Changes Mean
A few signal patterns recur. A slow rise in overall vibration at running speed often points to growing imbalance or looseness. A new peak at a bearing's characteristic frequency suggests wear on a specific surface. A rise in temperature without a matching change in load can mean lubrication trouble or friction. Oil debris counts that climb steadily, rather than spiking once, usually mean a component is wearing and not just shedding a break-in particle.
Experts combine these signals. A single sensor can mislead, but vibration, temperature and debris trends pointing the same way build a convincing case. This is why modern systems fuse several data streams instead of relying on a single threshold.
Maintenance Organizations and the Business Case
For repair stations, predictive data changes planning. If a customer's engine shows rising wear, the shop can order parts and schedule hangar time before the airplane arrives. That shortens turn times and reduces the number of airplanes parked waiting for parts. For manufacturers, the equivalent is scheduling a spindle rebuild during a planned shutdown rather than losing a shift to a failure.
The return is easiest to see on assets that are expensive to stop. An autoclave that runs long cure cycles, for example, cannot be paused midway without risking the parts inside. Monitoring heater, vacuum and pressure systems on such equipment pays for itself the first time it prevents a ruined load.
Regulation and Trust in the Data
In aviation, maintenance actions follow approved procedures, so predictive findings feed into those procedures rather than replacing them. Operators validate a monitoring method, show that it detects faults reliably, and then adjust inspection intervals under the approved program. This takes time, but it also builds trust. In a factory setting the rules are lighter, yet the same discipline applies: prove the alerts are right before acting on them automatically.
A Worked Example: A Machining Cell
Imagine a cell with three machining centers cutting titanium brackets. Spindle bearings on those machines wear faster than usual because of the material. The shop attaches accelerometers to each spindle housing and logs vibration and motor current. After a month of baseline data it sets an alert for a sustained rise above normal in the bearing frequency band.
Three months later the alert fires on one machine. Maintenance schedules a spindle swap over the weekend, replacing a bearing that was starting to fail. Without the alert, the bearing would likely have failed during a production run, scrapping the part in the machine and taking the cell down for days while a replacement spindle was sourced. The cost of the sensors was a small fraction of what one failure would have cost. That is the typical pattern, and it explains why the technology spreads once a shop sees one early catch.
Choosing a Vendor or Building In House
Shops can buy a packaged monitoring service, assemble a system from sensors and open software, or use the analytics already built into modern machine controls. Packaged services are faster but cost more over time. Do-it-yourself systems are cheaper but need staff time. Ask vendors how alerts are tuned, who owns the data, and whether the system works without a constant internet connection.
Where It Is Headed
Expect more onboard processing, better physics-informed models, and tighter links between condition data and parts ordering so that a replacement part arrives before the airplane does. Over time, maintenance planning will rely less on the calendar and more on measured condition. For Washington suppliers, the useful move is to start collecting clean condition data now. See also the Everett industrial IoT page for local resources.
